Gilbarco Sk700 Programming Manual Jun 2026

Gilbarco SK700 is a high-performance fuel dispenser known for its durability and modular design. Programming the unit correctly is essential for accurate fuel delivery, secure communications with Point of Sale (POS) systems, and overall forecourt efficiency. This article serves as a guide for technicians and site managers on navigating the Gilbarco SK700 Programming Manual , focusing on basic setup, configuration codes, and troubleshooting procedures. 1. Preparing for Programming Before modifying any internal parameters, the dispenser must be put into a state that allows configuration changes. Most high-level programming requires physical access to the processor board to engage "Calibration Mode" or perform a "Cold Start". Accessing the Electronics: Remove the cover over the CPU PCB to access the configuration switches and jumpers. Calibration Switch: For many settings, including meter calibration, the CAL switch must be moved to the left (CAL position). Cold Start Jumper: A cold start is typically only required for major re-configurations or to clear catastrophic memory errors. This involves moving a two-wire jumper to the "Cold Start" position before powering up. 2. Entering the Programming Menu Programming is performed using the Manager Keypad located inside the dispenser’s head unit. Press the F1 key to initiate the command entry. Enter the Master Code (the factory default is often 0128 ) and press ENTER . The display will show a 0 , indicating the unit is ready for a Function Code (FC) or Command Code (CC). 3. Essential Command Codes (CC) The SK700 uses a numerical menu structure where each "Command Code" corresponds to a specific dispenser function. Command Code Description Key Features CC 1 Unit Type & Mode Defines if the pump is standalone or console-controlled. CC 10 Price Per Unit (PPU) Used to set the fuel price for different grades and sides. CC 59 System Cold Start Clears application memory; used as a last resort for troubleshooting. CC 76 Meter Calibration Used in conjunction with a prover can to adjust meter accuracy. CC 80 Flow Rate Settings Sets maximum flow rates for different fuel grades (e.g., 40L/min vs 80L/min). CC 95 Country Code Configures default regional settings (e.g., Australia = 36). 4. Basic Post-Cold Start Setup If you have performed a cold start, you must re-initialize four primary parameters for the pump to function: Country Code: Sets default decimals and units. Pump Type: Identifies the hardware configuration (suction vs. pressure). Pump Numbers: Assigns IDs for communication with the controller. Protocol Setting: Configures the communication method (e.g., Gilbarco 2-Wire, IFSF-Lon). 5. Troubleshooting with Error Codes When the SK700 encounters an issue, it will display a specific error code on the price display. Understanding these codes is critical for rapid repair.

Accessing the Manual

Direct from Gilbarco : The first place to look for the programming manual would be directly from Gilbarco or its parent company, Verifone's, official website. Companies often provide product manuals and guides for download.

Gilbarco or Verifone Support : If you can't find the manual online, reaching out to Gilbarco or Verifone's customer support might help. They can provide you with the necessary documentation or guide you to where it can be found. Gilbarco Sk700 Programming Manual

Industry Forums and Communities : Sometimes, industry-specific forums or communities might have shared resources or experienced users who can provide guidance.

General Programming Considerations While I don't have the specific manual, here are some general steps and considerations for programming a device like the Gilbarco SK700:

Understanding Device Communication : Familiarize yourself with the communication protocols supported by the SK700, such as RS232, Ethernet, etc. Gilbarco SK700 is a high-performance fuel dispenser known

Configuring Dispensers : The SK700 is often used to control and monitor fuel dispensers. Programming would involve setting up which dispensers are connected, their configuration (e.g., number of hoses, fuel types), and how they interact with the payment terminal.

Payment Processing : Configuring the payment processing involves setting up the payment options (credit/debit card, cash, etc.), integrating with the host system for authorization and settlement, and possibly configuring encryption and security settings.

User Interface Customization : Depending on the requirements, you might need to customize the user interface of the SK700, including message screens, button mappings, and language settings. Accessing the Electronics: Remove the cover over the

Integration with Site Systems : The SK700 might need to integrate with other site systems, such as point-of-sale (POS) systems, loyalty programs, and back-office systems. This involves configuring the interfaces and possibly writing custom code.

Testing and Validation : After programming, thorough testing is essential to ensure that all functionalities work as expected. This includes testing dispenser control, payment processing, and integration with other systems.